The Following Article comes from Norm Kerr – Originally Published on the MG Experience 2011-03-23. Use by permission
First, read Section H of the Bentley Midget workshop manual.
These notes are meant as a supplement to the workshop manual. You can buy them on Amazon here:
If you have a huge freeplay between your ring and pinion, it is likely due to failed pinion bearings or failed thrust washers. The key question is this: the bearings and thrust washers are all replaceable, about $100 worth of parts. On the other hand, if the R&P teeth are worn, then you are probably best off replacing it rather than trying to repair this one. But, if the gear teeth all look very good (no dull spots, no chips, no scouring), it might be worth the effort.
If you want to find a shop to do this for you, google around for shops who do hot rods, or cars with RWD that get ratios changed for performance (in the US, this is easy: any shop that specializes in custom engine/driveline work on Mustangs, Camaros, etc.), they should be able to do the whole job, even setting up a new R&P (setting up a new R&P is substantially more involved than just replacing the bearings and thrust washers).
If you think your gears look good, and just need the bearings and washers replaced, then any good, local machinist ought to be able to do the remove / replace for you (and can check all of the lash, clearance, run-out and bearing pre-load for you, if you give them a copy of the pages out of the Bentley that describes the key values - frankly, most of the key info is universal to all differentials, and the stuff that isn't, is hand written (believe it or not) on the edge of your ring gear.
Or, you can do it yourself:
(photo of universal leverage thingy, made from a length of 1.5 x 1.5" angle iron, some flat stock, some drilled holes and some nuts/bolts)
Disassemble the pumpkin (re-assembly torque shown in parenthesis):
- Note the RH/LH bearing cap locations to make sure you put them back correctly later.
- Remove bearing caps (65 ft-lb torque)
- Lift bearing cage out
- Remove crown wheel from the cage (60 ft-lb torque)
- Tap out the retaining pin (item 24 in Bentley) from the crown wheel side (left hand side). Use an 1/8" drill to clean out the end of the hole if needed. After re-installation of this pin when done, peen over the edge of this hole to prevent the pin from being able to come out by accident.
- Remove pinion pin, planet and sun gears, and their thrust washers (items 19 ~ 23 in Bentley). Be very careful to keep each part in the same position when you put them back together
- Remove the pinion nut to remove the pinion gear, crush spacer, bearings, shim, seal, and dust cover (items 29 ~ 35)
The crush spacers supplied today are too strong, mine reached the specified 12in-lbs bearing preload at under 120ft-lbs (not the 140 ft-lbs the book says to go to). So, if you install a new crush spacer and go all the way up to 140, without checking the bearing load, and you got one of those strong spacers like I got (twice, since I overshot the first time) it'll overload things and quickly wear the bearings out.
This work can all be done with basic machine shop tools, if great care is taken to get everything back right where it came from, and if that new crush spacer is monitored very closely during the pinion nut torque:
- Dial indicator
- Hydraulic press (with various sized arbors for pressing)
- Bearing puller (for pulling the "inner" pinion bearing off of the pinion shaft)
- Seal puller (screwdriver, or small crow bar will do in a pinch)
- in-lb torque wrench
- Blueing ink (for checking R&P tooth alignment)
Last but not least:
- Clean and orderly work space to keep the parts in so they all go back in exactly the same place (like, the ring gear "clock" position relative to the cage, the planet and sun gears to each other, or the cage bearings on the right / left side).
Oh, and the in-lb torque wrench. Typical in-lb torque wrenches only go down to 50 or so. Note that the bottom 15% of any torque wrench is not to be used, so you need a smaller tool. We need 11 ~ 13 in-lb, so you need a special one designed for that low range (ideally, a 6 ~ 15 in-lb torque wrench). I bought mine from Precision Instruments. You can also use a small oz. spring scale and a bit of ingenuity, but I was surprised at how very useful it was to be able to rotate my pinion 360° and measure "all of the way around". Another way to do it is with a known weight and a moment arm marked off like this:
This home made tool consists of a 2 ft breaker bar with a known weight hanging from it. Once the tool is on the pinion nut in a horizontal plane, you then move the weight along the bar. In the case of a 1lb weight, 12 inches from the socket, and the bar in a horizontal plane, the force applied to rotate the pinion is therefore 12 inch lbs (torque = force x distance). Note that the force applied to the pinion should be measured when the pinion is already rotating (to eliminate any sticktion, or initial resistance to movement).
Note that when the crush spacer gets close to being compressed, the bearing load increases quickly in a very few degrees of nut rotation. If you overshoot, get a new crush spacer and try again (once over compressed, a crush spacer is scrap).
Parts needed:
Pinion bearings, cup washers, thrust washers, pinion seal, crush spacer, crown wheel lock tabs (3), diff pin, and the spring pin that holds that cross pin in the cage *.