| Technical Specifications | |||||
| Firing Order | 1-3-4-2 | ||||
| Valve Clearance | 0.012 (cold) | ||||
| Idle Speed | 1000 rpm | ||||
| Static Timing | 7º BTDC | ||||
| Dynamic Timing | 13º BTDC @ 1000 rpm | ||||
| Timing mark location | Timing cover, bottom | ||||
| Distributor type | Lucas 25D | Contact points | |||
| Points Clearace | 0.014 to 0.16 | ||||
| Rotor direction | Anti-clockwise | ||||
| Dwell angle | 60 | ||||
| Coil | Lucas | ||||
| Primary Resistance | 3 to 3.4 Ω | ||||
| Spark plug gap | 0.24" to 0.26" | ||||
| Carburetor | SU HS2 (x2) | 20 W/ 50 | |||
| Carburetor main jet | 90 | ||||
| Carburetor jet needle | ABC | ||||
| Engine type | 1275cc OHV I-4 | ||||
| Compression ratio | 8.8:1 | High compression | |||
| Engine bore | 2.78" | ||||
| Engine stroke | 3.2" | ||||
| Oil press Idle | 20 lbs | ||||
| Oil press Normal | 40 to 70 lbs | ||||
| Fuel pump | SU AUF216 | ||||
| Drivebelt tension | 0.5" | 13mm | |||
| Fuel Tank Capacity | 8.6 US Gallons | High Octane with Lead substitute | |||
| Cooling System Capacity | 7 US Pints | 50/50 | |||
| Cooling Filler cap press | 15 lb/ft | ||||
| Sump Capacity | 7.8 US Pints | 20 W/ 50 | |||
| Gearbox Capacity | 2.7 US Pints | 20 W/ 50 | |||
| Rear Axle Capacity | 2.1 US Pints | 90EP | |||
| Engine Data | |||||
| Crankshaft and Main Bearings | |||||
| Main journal diameter | 2.0005" to 2.0010" | ||||
| Main bearing length | 0.975" to 0.985" | ||||
| Crankpin journal diameter | 1.6254" to 1.6259" | ||||
| Main bearing diam clearance | 0.0010" to 0.0027" | ||||
| Connecting rods and Big-End Bearings | |||||
| Length b/w centers | 5.748" to 5.792" | ||||
| Big-end bearing length | 0.840" to 0.850" | ||||
| Endfloat on crankpin | 0.006" to 0.010" | ||||
| Big-end diam clearance | 0.0010" to 0.0025" | ||||
| Gudgeon Pin type | Interference | Hand push | |||
| Gudgeon Pin diameter | 0.8123" to 0.8125" | ||||
| fit to con-rod | 0.0008" to 0.0015" | ||||
| Pistons - Aluminium, solid skirt, dished crown | |||||
| clearance bottom of skirt | 0.0015" to 0.0021" | ||||
| clearance top of skirt | 0.0029" to 0.0037" | ||||
| Piston Rings | |||||
| Compression rings - type | Top | Internally chamfered, chrome | |||
| 2nd and 3rd | Tapered, cast iron | ||||
| width all | 0.615" to 0.625" | ||||
| Fitted gap | Top | 0.011" to 0.016" | |||
| 2nd and 3rd | 0.008" to 0.013" | ||||
| Ring to groove clearance | 0.0015" to 0.0035" | ||||
| Oil control ring - Duraflex 61 | |||||
| Fitted gap | 0.012" to 0.028" | ||||
| Valve Data | |||||
| Intake | Head diameter | 1.307" to 1.312" | |||
| Exhaust | Head diameter | 1.1515" to 1.565" | |||
| Intake | Stem diameter | 0.2793" to 0.2798" | |||
| Exhaust | Stem diameter | 0.2788" to 0.2793" | |||
| Stem to guide clearance | 0.0015" to 0.0025" | ||||
| Valve to rocker clearance | 0.012" (cold) | ||||
| Valve Springs | |||||
| Free length - inner | 1.703" | ||||
| Free length - outer | 1.828" | ||||
| Valve lift (intake & exhaust) | 0.318" | ||||
| Vavle guides | |||||
| Length | Intake | 1.6875" | |||
| Length | Exhaust | 1.6875" | |||
| Fitted height above seat | 0.540" | Intake & Exhaust | |||
| Valve Timing | |||||
| Timing marks | dimples on timing gears | ||||
| Rocker clearances | 0.029" | ||||
| Intake opens | 5º BTDC | ||||
| intake closes | 45º ABDC | ||||
| Exhaust opens | 51º BBDC | ||||
| Exhaust closes | 21º ATDC | ||||
| Torque Settings | |||||
| Cylinder Head Nuts Plain | 42 Ft/lbs | ||||
| Cylinder Head Nuts Stamped '22' | 50 Ft/lbs | ||||
| Con-rod nuts Plain | 40 Ft/lbs | ||||
| Con-rod nuts Nyloc | 32 Ft/lbs | ||||
| Crankshaft pulley bolt | 70 Ft/lbs | ||||
| Flywheel bolts | 40 Ft/lbs | ||||
| Main bearing bolts | 60 Ft/lbs | ||||
| Manifold nuts | 15 Ft/lbs | ||||
| Oil filter retaining nuts | 16 Ft/lbs | ||||
| Oil pipe union adapter | 20 Ft/lbs | ||||
| Rocker cover retaining bolts | 4 Ft/lbs | ||||
| Rocker pedestal nuts | 25 Ft/lbs | ||||
| Sump retaining bolts | 6 Ft/lbs | ||||
| Thermostat housing nuts | 8 Ft/lbs | ||||
| Timing cover 1/4 inch bolts | 6 Ft/lbs | ||||
| Timing cover 5/16 inch bolts | 14 Ft/lbs | ||||
| Water pump nuts | 17 Ft/lbs | ||||
| Fan securing bolt | 8 Ft/lbs | ||||
| Fuel tank drain plug | 9 Ft/lbs | ||||
| Mechanical fuel pump to block | 14 Ft/lbs | ||||
| Spark plugs | 20 Ft/lbs | ||||
| Rear extension to gearbox bolts | 18-20 Ft/lbs | ||||
| Drive flange nut | 90-100 Ft/lbs | ||||
| Brake disc to hub | 43 Ft/lbs | ||||
| Brake caliper to stub axle | 48 Ft/lbs | ||||
| Brake pressure failure warning valve & plug | 16 Ft/lbs | ||||
| Alternator pulley nut | 25 Ft/lbs | ||||
| Starter motor retaining nuts | 34 Ft/lbs | ||||
| Steering column upper fixing bolts | 12-17 Ft/lbs | ||||
| Steering column pinch bolt | 9-12 Ft/lbs | ||||
| Steering rack housing clamp bolts | 20-22 Ft/lbs | ||||
| Steering rack mounting bracket bolts | 17-18 Ft/lbs | ||||
| Tie rod ball joint nut | 28-32 Ft/lbs | ||||
| Tie rod end assembly locknut | 30-35 Ft/lbs | ||||
| Tie rod rack locknut | 80 Ft/lbs | ||||
| Front & Rear damper bolts | 25-30 Ft/lbs | ||||
| Front hub castellated - Disc | 55-60 Ft/lbs | ||||
| trunion retaining nut | 40 Ft/lbs | ||||
| Steering wheel nut | 37 Ft/lbs | ||||
| Roadwheel lug nuts | 45 Ft/lbs | ||||