I have double checked this against as many wiring diagrams as I can. Jest be aware that your car may vary depending on year. This is a basic guide on what to do if you turn the key and the engine wont spin over.
Start by checking to make sure that the engine is grounded. Connect one end of the test light or digital multimeter (set to voltage or continuity) to the positive terminal on the battery, and then touch the other probe or the test light to head studs, or a intake or exhaust manifold or anything metal that is bolted to the engine and is not electrically insulated from it. The metal shell (with the hex on it) on a spark plug is a good spot. You should see voltage or continuity. If not, you have a faulty ground strap and the engine will not turn over and you will not have a functioning ignition system. Other problems may include a temp and oil pressure gauges that don't work (if they are electrical as on some 1500 cars).
If the ground is good, bridge the two big terminals on the solenoid with a big fat screwdriver and see if the starter spins and the engine cranks. If it does, your problem isn't the starter or the connections. If it doesn't spin, check the connections at both the solenoid and the starter are good and tight and check them with a multimeter to make sure they are good connections. Also check to make sure that the starter is properly grounded to the engine. It is very unlikely that it isn't but I suppose it's possible that the starter has a bad ground somehow. If everything else checks out at this point, you have a bad starter or a starter related problem.
If the starter spins but the engine doesn't, make sure the engine turns over by hand by using a wrench or socket on the crank pulley bolt with the car in neutral, or put it in 4th gear and push the car backwards and see if the engine turns. If the engine turns, and the starter turns, but the starter wont turn the engine, remove the starter and inspect the starter pinion and make sure that everything moves freely. Also inspect the teeth on the flywheel ring gear through the hole in the engine backplate that the starter came out of.
The next step is to figure out if the solenoid works (for simplicity sake I am calling the high current starter switch on early cars a "solenoid" as it may be tested in a similar manner). Solenoids have 3 terminals (yes I know early cars may have only two). Two high current cables for the battery and starter, and one small spade connector that gets power from the ignition switch. On most spridgets there are also some brown wires (one or more) that connect at the battery terminal on the solenoid (to connect the battery to the rest of the electrical system), but early cars may have this brown wire connected directly at the battery. There may be other connections here depending on your year and what kind of distributor you have installed.
Some later models with a Lucas Electronic ignition system have a white/light green wire connected somewhere on the solenoid. The terminal you need to look for is the one with a White/Red wire connected to it. It should be (and usually is) the only small spade connector that is located between the two high current terminals (on the side of the unit) and not directly bolted to either of the high current terminals. If you jumper this terminal to the high current terminal that has a brown wire connected to it, the starter should spin and the engine should turn over. If it does, then the fault is either in the wiring between the ignition switch and the solenoid, or it is a fault in the ignition switch itself. The earliest cars have a mechanical cable attached to the solenoid and no additional wiring, so other checks in this system are not needed.
Test the ignition switch by using a digital multimeter set to continuity or a test light. Check to see that when the switch is turned to the start position, the white/red wire coming out of the switch, is electrically connected to the Brown or Brown/Purple wire coming out of the switch. If not, your switch is bad and should be replaced. The wires usually terminate in bullet connectors or a multi pin plug, so you wont have to remove the switch to check it.
If the switch checks out, the problem is in the wiring harness itself. Most likely a bad connector, but it is also possible that the white/red wire is somehow shorted to ground or open.
Best of luck diagnosing the problem, hope that helps somebody.
-Seth 1/1/15