Kangol Magnetic Seatbelts

 

  The seatbelts for my Midget were made by Kangol. These magnetic lift flap seatbelts were the stock type for a number of years until they were replaced with auto retracting belts. The earliest sprites and midgets did not have seatbelts at all, and I'll have to do some digging to figure out exactly when these Kangol belts were first issued as standard equipment. However, it is clear from the June 2, 1961 Autocar that BMC began including anchor points for seatbelts mid 1961 (around the same time as the launch of the MKII Sprite and MKI Midget).

  I believe Kangol now makes hats and fashion wear. The patent on the idea for lift flap magnetic seat belts in the US is patent number 3127650. I have compiled that patent file into a pdf (KangolPatent.pdf). The US patent was filed in the US March 12, 1962 by William Henry Seward, Havant, England, assignor to Kangol Helmets Limited, London, England. The patent also states that the British patent 942282 was filed March 14 1961.

  Apparently, the first belts of this type available, had buckles made entirely of metal as shown below (thanks to Paco Moreno de Barreda of Madird Spain for the photos). These appear to most closely resemble the patent drawings of any of the variations used on sprites or midgets.

Here are more shots of this style of belt from Robert Garb (1843lamp) of the MG Experience forum. Click to enlarge. These belts had unusual shoulder mount brackets that featured two studs welded to the top of the fender wells.

Here is an illustration of this belt installed in the car

Here is a picture of the box they often shipped in if you ordrered a set to install yourself. Note the logo on the latch that is missing from the other pictures shown thus far ( click to enlarge).

I have seen some earlier plastic buckle examples with a BMC logo rather than a British Leyland logo. These were apparently used from 1965-1969. All seatbelts had clotch labels sewn onto them. It is very hard to find ones with the labels intact. The following pictures are courtesey MGBBrown. Click to enlarge

 

 

  This type of belt was also found on W111 and W113 Mercedes of the era, as well as Fiats, Jaguars, MARCOS, Lotus, Porsche 912, Volkswagens, Austins, MGB, Triumphs, and many many other cars. Each belt had a sticker on it that displayed the marque of the car's manufacture. However, it was possible to order belts direct from Kangol, and these had Kangol's magnetic belt logo.

 

  In the 1970-1972 Midget, they would have originally looked like this (the picture on the left is from the 1971 sales brochure) the on the right are some MGB belts I used for parts). You will note the unusually shaped hole in the tab shown on the left edge of the picture below right. This was a special shoulder release availible on some models. This was patent number 3458233 and was filed by Kangol Magnet Ltd on March 6. 1968. There was a plastic insert that went into the fat end of the hole, and allowed the shoulder belt anchor to be released when the plastic insert was pressed in with your thumb.

  However 30-40 years of wear and tear left the driver side looking like this

 

The passenger side looked a little better.

  These belts are no longer in production and haven't been for years. If you want to preserve this unique original feature you have little choice but to collect the parts required, and send them off to a seatbelt repair shop for rewebbing. The cost of replacement parts varies. I saw some jaguar buckles that were going for almost $200 and a complete set of new old stock kangol magnetic logo belts that were going for only $75. The most valuable piece seems to be the sticker on the buckle, with the buckle being the next most expensive, and the rest of it being somewhat inconsequential to the asking price. I found some belts off of an MGB on ebay in great shape and used some of the buckles and hardware while removing the parts I that were incompatible with the Midget.

  I chose Ssnake-Oyl Products of Texas for the restoration, and sent off the good parts along with my old belts (to use as a pattern and for a few more parts). The way they do business is you send in your old belts, they examine them and send you an estimate, and then if you agree to pay that amount, they will begin work on your belts. Expect about 2-3 weeks for them to finish restoring them from the time they receive payment. I don't recommend attempting to sew your own as it does require a special sewing machine please leave this to a professional. Alternately you could just toss them in the trash and get an aftermarket set from Moss, but to me at least, push button seatbelts are so common, lift flap buckles are a nice feature worth preserving if you have them.

Last Revised 5/8/2013 by Seth Jones

See the results here